This is brand new pair of control levers in silver chrome finish.

These are the earlier axial lever type to suit models that are fitted with master cylinders that have a 12mm pivot bolt size.

These are suitable for Ducati as per the list below.


Genuine levers are incredibly expensive. We have a pair of top quality replica levers here at a fraction of the cost. Learn More

This is brand new Front & Rear Paddock Stand set for single sided swing arm models

This is a set of paddock stands, one front and one rear.

Paddock stands are suitable for general maintenance and repair work. Side paddock stands utilise a locking adaptor pin which inserts and locks into the rear axle.

We also have these listed in our shop as a rear stand on it's own, should that be required instead.

This rear stand fits the Ducati models with single sided swing arm as the list below.


The Ducati 1098 had two different versions of rear spindle. From May 07 onwards it used a rear spindle that will use this 40mm pin rear paddock stand. All Ducati 1098 manufactured before May 07 use a 42mm pin, please look at our other items for this. If you are unsure, please measure the left hand side of the rear spindle to confirm prior to ordering.br>
Front stand is universal so could easily be used on a variety of other bikes.

Front stand has spring loaded quick release under fork adaptors.

Heavy duty nylon wheels.

These stands are NOT intended for storage use.

Tough powder coated red finish. Learn More

NTN Brand new top quality pair of swing arm pivot seals for Ducati machines.

These fit on the swing arm each side of the needle roller bearings.

Equivalent Ducati part no 0412.02.295 or also 930.5.012.1A

These are supplied as a pair and are to fit the Ducati models listed in the pull down box below.

Learn More

New 38 tooth 520 pitch alloy rear sprocket by JT Sprockets

The photo above is a generic picture for representation purposes, you will receive the correct fitment rear sprocket to fit your machine, with the dimensions and format as below:



Note: this is a 520 conversion sprocket and will only fit if all of your final drive is 520 pitch, rather than the OEM 525 pitch.

Please also note that this rear sprocket requires the use of a sprocket carrier adapter. We have these available should you not already have one. This sprocket will fit the JT sprocket carrier and also the Renthal sprocket carrier, but no other brand of sprocket carriers. Please call or email us should you require further information regarding possible fitment.

This will fit the following models.


* 38 tooth 520 pitch alloy rear JT sprocket

* Note * This is part of a 520 conversion on the above models, as they are either 525 or 530 pitch as OEM, depending upon model. So you would need to convert all of the final drive on those models. We have other sprocket tooth variations for these machines in the shop, please take a look. Learn More

The SBS DC Dual Carbon road racing compound has since the introduction in 2001 proven to be the ”Choice of Champions”.

World top racing teams have achieved a long row of race wins, lap records, national and World Championship titles in Superstock, Supersport, Superbike and Endurance racing using SBS Dual Carbon pads.

Characteristics:
• Thermal bedding-in and brake fade eliminated by use of DEST technology.
• High initial bite.
• High friction level and progressive brake feel.
• High thermal stability.
• Consistent brake performance and brake lever position.
• Low pad wear.
• Rotor friendly due to transfer film generated on disc surface.
• Available for the majority of new Superstock, Supersport and racing brake calipers.
• Recommended for top level international and national championship road racing.
• These are for race use only!

This is one caliper set of Dual Carbon (DC) compound front brake pads.

These are to fit all of the machines in the pull down list below.


The dimensions and format of the pads are as below:


If you have a twin caliper machine then you will need to order a quantity of 2, as you will need one set per caliper.

SBS' sublime braking properties are the result of systematic, sustained product development that focuses on creating the optimum combination of performance, durability, and safety. Knowledge, experience, and enthusiasm are the motive force in our R&D department where staff constantly set new standards and can always fulfil the demands of the best riders.Tests and more tests are a central aspect of our R&D. We perform tests on the basis of various methods in order to ensure the best results before products are launched.

Par number: 706DC
EAN number: 5703858179779

SBS promotional video



SBS brake pads are used and trusted throughout the Road Racing World Championships.

Superbike World Championship
Ten Kate Honda Racing
Althea Ducati Racing
Supersonic Racing Team

Supersport World Championship
Ten Kate Honda Racing
Kawasaki Racing
Harms Benjan Racing

Superstock European Championship 1000
Ten Kate Honda Racing
Garnier Junior Racing BMW
Team All Service System by QPD
Team MRS Yamaha France
Yamaha Italia

Superstock European Championship 600
Ten Kate Honda Racing
BWG Racing
Team MRS Yamaha France
Team Trasimeno Yamaha Italia
Team All Service System by QPD
Team MTM Racing

Endurance World Championship
Team Bolliger Kawasaki
Team RAC41
Team Phase One Endurance
Qatar Endurance Racing Team

BEDDING-IN PROCEDURE FOR SBS-DC
When changing for SBS-DC from using another type of brake pad material - Follow this Bedding-in procedure very carefully:
1. Remove existing friction material deposit from brake discs - using eg. emery paper #150.
2. Do a series of gentle brakings until pad-surface is in full contact with disc-surface.
3. After pad/disc contact is achieved - repeated short brakings building up heat in discs and pads until a very thin and uniform dull/black/darkblue layer of friction material (transfer film) is established on the brake disc.
4. Then a period to allow discs to cool again before proper use.
5. Then a few easy laps building up heat - ready for race use.

When bedding-in procedure IS needed
Always follow the above bedding-in procedure - when changing for SBS-DC for the first time OR when using new brake discs.

When bedding-in procedure is NOT needed
When brake discs are covered by SBS-DC friction material (transferfilm) - new pads only need about one/two laps to be in full contact with disc-surface - then the pads are race ready (Thermal bedding-in as described above in point 1. - 4. is not needed)
Cleaning of brake discs - NOT when using SBS-DC
When brake discs are covered by SBS-DC friction material (transferfilm) - Do not clean/sand/grind the brake discs after each session. Learn More

New 45 tooth 520 pitch rear sprocket by JT Sprockets

The photo above is a generic picture for representation purposes, you will receive the correct fitment rear sprocket to fit your machine, with the dimensions and format as below:


This will fit the following machines.


* 45 tooth 520 pitch steel rear JT sprocket.

We have other sprocket tooth variations for these machines in the shop, please take a look.
Handy replacement spare service part for your Ducati motorcycle

EAN number: 824225311372
Part number: JTR735.45 Learn More

Renthal highly developed grip glue, specially formulated to give a secure bond without damaging the grip.

This is a universal item but we know that they are also suitable for the following Ducati's


We also have Renthal grips and clean grips in our Shop, please take a look. Learn More

Brand new light weight billet alloy sprocket carrier. Makes changing rear sprockets quick and easy.

This gives a performance advantage as it will reduce un-sprung mass at the rear hub. This helps to improve both acceleration and turn in due the lower inertia generated at the rear hub.

The pattern is correct to accept sprockets from the big name manufacturers including Renthal & JT, so there are plenty of options for sprocket choice.

A very high spec piece of kit that also implements a cush drive saver. The extra pieces of alloy around the rear of each cush drive as shown, stops fatigued cush drive bobbins from separating and causing damage to the eccentric rear hub. This is a known weak point on rear cush drives and eliminated by this sprocket adapter.

This will fit the following models.


Fitting a quick release sprocket adapter means no more reaching for a huge socket to remove the sprocket carrier when changing the rear sprocket.

Changing a rear sprocket with one of these fitted is done with minimal tools in a matter of minutes. Learn More

New 38 tooth 525 pitch rear sprocket by JT Sprockets

The photo above is a generic picture for representation purposes, you will receive the correct fitment rear sprocket to fit your machine, with the dimensions and format as below:



This will fit the following models.


* 38 tooth 525 pitch alloy rear JT sprocket

We have other sprocket tooth variations for these machines in the shop, please take a look.

Note: This rear sprocket requires the use of either the JT Sprockets or the Renthal quick release rear carrier. You will NOT be able to use this sprocket unless you already have one of these fitted.

We have the JT Sprocket carrier available in our shop, please take a look in this section and it is the first item listed. Learn More